Note #1: After Login has been carried out you need to recode the control module.
Note #2: Special Login 07499 is used for 6-Cylinder Diesel Engine with 1LG Brakes and Multitronic.
Note #3: The Production Codes (PR-Code) such as 1LX can be found on a Sticker near the Spare Tire Well and/or the 1st Page of the Service Manual. Click here to see an Example of a Sticker.
0?xxx: Chassis 8 = VW Passat W8
9 = VW Passat
0x?xx: Brakes 3 = (PR-1LT/1LF)
4 = (PR-1LC/1LX/1ZF/1LZ/1ZG)
5 = (PR-1LB/1LE/1ZC)
6 = (PR-1LZ/1ZJ)
0xx?x: Engine 5 = (PR-T5X/T4N/T9J*/T6T/T1K/T1E/T7F*) (* with Brakes: PR-1LB/1LE/1ZC)
Note #1: Coding is accepted after a specific login has been carried out.
Note #2: After successful coding the steering angle sensor basic setting needs to be carried out.
Note #3: The Production Codes (PR-Code) such as 1LX can be found on a Sticker near the Spare Tire Well and/or the 1st Page of the Service Manual. Click here to see an Example of a Sticker.
Note #4: In some cases, you will need to enter a non-zero WSC, such as 12345.
0?xxx: Chassis 4 = VW Passat
5 = VW Passat W8
0x?xx: Brakes 1 = (PR-1LZ/1ZJ)
2 = (PR-1LB/1LE/1ZC)
3 = (PR-1LC/1LX/1ZF/1LZ/1ZG)
4 = (PR-1LT/1LF)
0xx?x: Engine 5 = (PR-T5X/T4N/T9J*/T6T/T1K/T1E/T7F*) (* with Brakes: PR-1LB/1LE/1ZC)
Vraag
antonio
Voor de mensen die de upgrade hebben uitgevoerd naar 312 mm remschijven voor de 3BG
Ik heb gelezen dat de abs module herschreven moet worden. Dit is met de ABS module Bosch 5.7.
Voor de Bosch module 5.3 is het volgens mij niet nodig.
De code voor de 312mm schijven is 1LT
VW Passat (3B) Brake Electronics (Bosch 5.7)
Contents
1 Login
2 Coding
3 Basic Setting 3.1 Steering Angle Sensor (G85) Calibration 3.1.1 Special Notes
4 Video Link
Login
Note #1: After Login has been carried out you need to recode the control module.
Note #2: Special Login 07499 is used for 6-Cylinder Diesel Engine with 1LG Brakes and Multitronic.
Note #3: The Production Codes (PR-Code) such as 1LX can be found on a Sticker near the Spare Tire Well and/or the 1st Page of the Service Manual. Click here to see an Example of a Sticker.
0?xxx: Chassis 8 = VW Passat W8
9 = VW Passat
0x?xx: Brakes 3 = (PR-1LT/1LF)
4 = (PR-1LC/1LX/1ZF/1LZ/1ZG)
5 = (PR-1LB/1LE/1ZC)
6 = (PR-1LZ/1ZJ)
0xx?x: Engine 5 = (PR-T5X/T4N/T9J*/T6T/T1K/T1E/T7F*) (* with Brakes: PR-1LB/1LE/1ZC)
7 = (PR-T0B/T10/T6V/T0D/T0F)
9 = (PR-T7F/T9H/T9J)
0xxx?: Transmission 5 = Manual (PR-G0C/G0K/G0G/G0L)
7 = Automatic (PR-G0E/G0F/G0Q)
Coding
Note #1: Coding is accepted after a specific login has been carried out.
Note #2: After successful coding the steering angle sensor basic setting needs to be carried out.
Note #3: The Production Codes (PR-Code) such as 1LX can be found on a Sticker near the Spare Tire Well and/or the 1st Page of the Service Manual. Click here to see an Example of a Sticker.
Note #4: In some cases, you will need to enter a non-zero WSC, such as 12345.
0?xxx: Chassis 4 = VW Passat
5 = VW Passat W8
0x?xx: Brakes 1 = (PR-1LZ/1ZJ)
2 = (PR-1LB/1LE/1ZC)
3 = (PR-1LC/1LX/1ZF/1LZ/1ZG)
4 = (PR-1LT/1LF)
0xx?x: Engine 5 = (PR-T5X/T4N/T9J*/T6T/T1K/T1E/T7F*) (* with Brakes: PR-1LB/1LE/1ZC)
7 = (PR-T0B/T10/T6V/T0D/T0F)
9 = (PR-T7F/T9H/T9J)
0xxx?: Transmission 5 = Manual (PR-G0C/G0K/G0G/G0L)
7 = Automatic (PR-G0E/G0F/G0Q)
Basic Setting
Steering Angle Sensor (G85) Calibration
Before starting the procedure turn the steering wheel at least 30 ° left and back straight ahead.
[Meas. Blocks - 08]
Group 005 Field 1 (Steering Angle Sensor -G85-)
Specification: 0.0 °
Tolerance (when straight): ±5.0 °
[Done, Go Back]
[Login - 11]
Enter 40168
[Do It!]
[basic Settings - 04]
Group 001
[Go!]
[Done, Go Back]
[Fault Codes - 02]
All fault codes should have disappeared.
[Done, Go Back]
Link naar reactie
Delen op andere sites
22 antwoorden op deze vraag
Aanbevolen berichten